SONY TA-1130
¥ 88,000 (released in 1972)
Commentary
SONY's ES series pre-main amplifier developed with the aim of "colorless, transparent and warm sound quality".
In the preamplifier section, 8 FETs out of 10 FETs are used, and each FET is operated with a margin at the best operating point.
In addition, this FET employs a specially developed NF (Noise Figure) that is extremely low, and noise is not a concern even when using a moving coil type cartridge with a low output voltage of several mV.
All stages of the power amplifier are directly connected, and no coupling capacitor is used.
As a result, the output, distortion characteristics and damping factor are not reduced even in a low frequency range compared with an output circuit using a conventional capacitor, and high-quality low-frequency reproduction is possible.
Equipped with a quick access switch that allows easy selection of Phono1, Tuner and one pre-selected input with a lever.
In addition to the high and low filters, it is also equipped with a loudness switch to compensate for the sense of hearing at low volume.
The preamp and power amp can be used independently by using the switches on the back.
You can use two pairs of speaker systems.
The AUX3 input is provided as a jack on the front panel for easy connection.
It is equipped with a speaker protection circuit for abnormal operation of the amplifier, and a load impedance detection type protection circuit to protect the transistor even if the speaker terminal is shorted by mistake.
Model Rating
Type | All-silicon transistor stereo premain amplifier | ||||||||
Circuit system |
|
||||||||
Power Amplifier Unit | |||||||||
Output (0.1% harmonic distortion factor) |
|
||||||||
Output band characteristic | 7 Hz to 30 kHz | ||||||||
Harmonic distortion factor | 0.1% or Less (at Rated Output) 0.05% or Less (at 1W Output) |
||||||||
Cross modulation distortion factor (60Hz:7kHz=4:1) |
0.1% or Less (at Rated Output) 0.05% or Less (at 1W Output) |
||||||||
Frequency characteristic | 10 Hz ~ 200 kHz, + 0 -2dB at 1W Output | ||||||||
Input Sensitivity / Impedance | Power Amp Input : 1V/90k Ω (at rated output) | ||||||||
Output terminal | Speaker : 2 lines Headphone : Load impedance 8 Ω or more |
||||||||
Damping factor | 100 or More (1 kHz, 8 Ω) | ||||||||
Signal-to-noise ratio | 110 dB or more (closed circuit) | ||||||||
Residual noise | 0.008 μ W or less | ||||||||
Preamplifier Section | |||||||||
Input Sensitivity / Impedance | Phono1, 2 : 1.2mV/47k Ω Tuner, AUX1, 2, 3, Tape Rec/PB (input section) : 130mV/100k Ω |
||||||||
Maximum allowable input | Phono1, 2 : 70 mV | ||||||||
Output Level / Impedance | Pre Amp Output : 1V/5k Ω Rec Out : 150mV/10k Ω Rec/PB (Output Part) : 30mV/82k Ω |
||||||||
Harmonic distortion factor | 0.1% or Less (1 kHz, Rated Output) | ||||||||
Cross modulation distortion factor | 0.1% or Less (at Rated Output, 60 hz : 7 khz = 4 : 1) | ||||||||
Frequency characteristic | Phono1 and 2 : RIAA curve ± 0.5 dB Tuner, AUX1, 2, 3, Tape Rec/PB (input) : 10 Hz to 100 kHz, + 0 -2dB |
||||||||
Loudness control (Volume -30dB) |
50Hz:+8dB 10kHz:+3dB |
||||||||
Tone control | Bass : 100 Hz ± 10 dB Treble : 10 kHz ± 10 dB (2 dB step, 10-step switching) |
||||||||
Filter | Low Filter : 100 Hz or less, 6dB/oct. High Filter : 7 kHz or higher, 6dB/oct. |
||||||||
S/N ratio (A-network) | Phono1, 2 : 70 dB or more (input 1.2 mV) Tuner, Aux1, 2, 3, Tape Rec/PB (input section) : 90 dB or more (input 130 mV) |
||||||||
<General> | |||||||||
Semiconductor used | Transistor : 33 FET:8 Diode : 36 SCR:1 |
||||||||
Pwer | 100 VAC, 50Hz/60Hz | ||||||||
Power outlet | Total 300W (2 interlocking systems, 1 non-interlocking system) | ||||||||
Power consumption | 155W | ||||||||
External dimensions | Width 400x Height 149x Depth 327 mm | ||||||||
Weight | 13kg | ||||||||
Attachment | Four pin plugs, one spare fuse (5A) | ||||||||
Sold Separately | Eurasian Cheek Finish Wood Case TAC-1 (¥ 4,600) Mounting Bracket MB-5 (¥ 2,800) |