SONY TA-1120
¥ 88,000 (released in 1965)
Commentary
The first all-silicon transistor premain amplifier in Japan.
Silicon transistors, which are resistant to temperature and have good high-frequency characteristics, are used in preamplifiers and power amplifiers, and are guaranteed for life in catalogs.
The circuit uses a quasi complimentary service SEPPP OTL circuit.
Equipped with a lever-operated quick-access switch, you can select your regular Tuner and Phono1 at the touch of a button, or you can preset one of the other inputs and use the lever to select these three.
This allows unused inputs to be skipped and prevents unpleasant noise from being generated.
Equipped with low filter and high filter.
Equipped with 2-dB-step tone control.
There is also a tone control cancel switch that allows the tone control circuit to be skipped and flat regardless of the position of the knob.
Model Rating
Type | All-silicon transistor stereo premain amplifier | ||||
Circuit system | Quasi complimentary service SEPPP OTL circuit | ||||
Power Amplifier Unit | |||||
Output | Non-clip music Power : 160W (8 Ω, both channel operation) Music Power (IHFM Standard) : 60W + 60W ± 0.5 db (8 Ω)
|
||||
Strain Rate (IHFM Standard) |
|
||||
Cross modulation distortion factor | 0.3% or Less (Rated Output, SMPTE Standard, 70 Hz : 7 kHz) | ||||
Frequency characteristic | 10 Hz ~ 100 kHz + 0 -1dB at Rated Output | ||||
S/N ratio (IHFM standard Cross-circuit) |
110 dB (ASA Standard Z24.3-1944 40 dB (A) curve with weights applied) |
||||
Input impedance | 100k Ω or more | ||||
Damping factor | 70 or More (1 kHz) | ||||
Sensitivity | 1 V (at 50W output) | ||||
Preamplifier Section | |||||
Output | Preamplifier output : 1.5 V Rec output : 0.2 V |
||||
Distortion Factor (at 1.5 V output) | 0.1% or Less (1 kHz) 0.1% or Less (30 Hz) 0.2% or Less (15 kHz) |
||||
Frequency characteristic | Tuner, AUX : 30 Hz to 100 kHz + 0 -2dB (use 30 Hz or less low-cut filter) Phono1, 2 : 30 Hz to 15 kHz ± 0.5 dB (flatness correction characteristic by RIAA equalizer) MIC : 30 Hz ~ 50 kHz + 0 -2dB
|
||||
Sensitivity | Tuner, AUX : 200mV/100k Ω (adjustable with 250k Ω semi-fixed) Phono1 : 5mV/47k Ω Phono2 : 1mV/47k Ω Tape Head : 1mV/500k Ω (ideal for 4.5k Ω read head) MIC : 2mV/500k Ω |
||||
Tone control | Bass : 100 Hz ± 10 dB Treble : 10 kHz ± 10 dB (2 dB Step 11-Stage Switching) |
||||
Filter | Low Filter : 50 Hz or less, 12dB/oct. High Filter : 9 kHz or higher, 12dB/oct. |
||||
S/N ratio (IHFM standard) | AUX, Tuner : 90 dB or more Phono1 : 80 dB or more Phono2 : 70 dB or more Tape Head : 70 dB or more MIC : 65 dB or higher (measured with weights on the 40 dB (A) curve of ASA Standard Z24.3-1944) |
||||
<General> | |||||
Semiconductor used |
|
||||
Pwer | 100 VAC (Switchable to 117 V, 220 V, 240 V) ± 10%, 50Hz/60Hz | ||||
Power outlet | Power switch interlock : 2 systems Power switch not linked : 1 system |
||||
Power consumption | No signal : about 30W Rated output : approximately 200W |
||||
External dimensions | Width 400x Height 145x Depth 310 mm | ||||
Weight | Approximately 11 kg | ||||
Attachment | Short plug Pin plug Connection code Silicon cloth 5A fuse |
||||
Sold Separately | Eurasian Cheek Finish Wood Case TAC-1 (¥ 4,600) Mounting Bracket MB-5 (¥ 2,800) |