BARCO/EMT EMT981
¥ 897,000 (released in December 1989)
Commentary
A CD player developed for professionals.
Equipped with track / index selector by track dial, direct skip during performance is possible.
In addition, it is equipped with a CUE search dial and CUE button that can set the start position accurately with one frame precision.
It is equipped with program performance functions such as AUTO CUE, which can automatically store the starting position of performance, GOTO, LOOP, and optional section REPEAT. Up to four types of memory sets are available.
Equipped with ON LINE (on-air) mode, all controls other than memory are automatically locked to prevent malfunction.
Equipped with a monitor speaker, it can be used for pre-listening, etc.
The speaker amplifier is equipped with a compressor switch so that you can listen to the low-level signal by increasing it.
Equipped with a headphone port and a monitor output port.
The VARISPEED knob allows you to vary the rotational speed of the disc within ± 10%.
Normal speed can be restored with one push.
Equipped with AES format digital output terminal.
Equipped with CLOCK IN/OUT jacks (BNCM jacks) for synchronizing the digital unit.
External control via RS232/SMPTE bus (switching type, 9 pin Min D terminal) and display data display are available.
Equipped with a REMOTE connector (15 pin Min D connector) for external control of fader start and other main functions.
The operation mode setting can be changed with the Configuration switch.
Both the Line output and Monitor output are equipped with independent left and right potentiometer for fine adjustment of the level.
Conversion adapter plug (pin-jack terminal) for unbalanced output is included.
Options included monoline output and battery buffer RAM (for memory backup in case of power failure).
Model Rating
Type | CD Player |
Line output | XLR Mx2 (L/R) equilibrium |
Output impedance | 50 Ω or More (40 Hz ~ 20 kHz) |
Output level | 12 dBu (adjustable from -10dBu to + 21 dBu) |
Signal-to-noise ratio (RMS) | 105 dB or more |
Total harmonic distortion rate (1 kHz) | 0.004% or less |
Frequency characteristic | 40 Hz to 20 kHz ± 0.2 dB |
Crosstalk (1 kHz) | -100dB or less |
Monitor output | 9 pin Min D F (L/R), with external mute input) unbalanced |
Monitor output level | +12dBu |
Built-in monitor amplifier | mono10W (4 Ω) Compressor On / Off |
Headphone out | Stereo 6.3 mm φ Standard Jack 5.5V/100 Ω |
Digital output | XLR M AES Standard 5Vp-p Output / 110 Ω |
Clock in/out | TTL Level Clock frequency : 44.1 kHz ± 10% |
Remote terminal | (TTL level output, TTL level input or switch contact) Fader Start 1 Control input 7 : Start / Stop, Edit / Online, Next track Front track, pre-begin, pre-end, and go-to-last control) Signaling output 3 : online, start fader / on-air |
Configuration switch | DIP switch Monitor Mute On / Off Fader no/nc (fader contact) Cue On / Off at end of specified interval Fader / on-air (signal output switching) Test On / Off RS232/SMPTE Bus Switching |
RS232 Interface | Configuration 45.5 to 38.4k boards |
SMPTE Bus | Configuration 38.4 board According to SMPTE207M Device addresses 1-15 |
Operating temperature | + 10 ° C to 60 ° C |
Relative humidity | 30% to 90% (non-condensing) |
Pwer | 115 VAC ± 10%, 45 Hz ~ 65 Hz |
Power consumption | 45VA |
External dimensions | Width 445x Height 88x Depth 375 mm |
Weight | 8kg |
Attachment | Conversion Adapter for Unbalanced output (pin jack) |