Audio Database

Image of Integra A-733mkII/120
Commentary

MKII series pre-main amplifier.

In addition to the basic concept of the Integra, it also takes usability into consideration. It is equipped with a 3-stage switching input circuit and a 2-system tape terminal for mutual recording.

In tone amplifiers, various elements, including the NF circuit that controls tone characteristics, change the rise and fall characteristics of middle and low frequencies, which adversely affect sound quality. This part of the MKII series that had been overlooked in the past has been thoroughly clarified by computer simulation and various problems have been solved.
In the tone amplifier, a variable β circuit is inserted in the NF circuit to give tone characteristics, and it has four time constants in the ultra-low frequency range. If this time constant is not carefully selected, a flat amplifier with excellent feedback stability cannot be realized. In the MKII series, a circuit that is advantageous to ensure feedback stability in a sufficiently low frequency range is selected and adopted, and a stable circuit with a large phase margin is realized.
In addition, in order to keep the high-pass cutoff high with a simple circuit while taking into consideration the balance between the high-pass and low-pass, and to ensure sufficient dynamic range even with a simple configuration, we have adopted a unique 2-stage circuit with a differential 1-stage emitter grounding.

In order to improve the signal-to-noise ratio, we have selected a PNP type transistor for the tone amplifier section, which has less 1/f noise due to its structure, and set the impedance level at the best point of the noise characteristic of the transistor.

In order to eliminate adverse effects of power supply voltage fluctuations, a differential circuit is used for the tone circuit, which is less affected by voltage fluctuations. In addition, the voltage is supplied through a ± 2 power supply type low voltage circuit with a voltage fluctuation rate of 1.7%, which prevents intermodulation due to voltage fluctuations in the power amplifier section.

Pure complimentary service with improved transient response characteristics in all stages Technologies developed in the conventional Integra series, such as power amplifiers with all stages connected directly, and operational amplifier type equalizer circuits, have also been introduced.

The wood case was sold separately as an option.

Model Rating
Type Pre-main amplifier
Power Amplifier Unit
Rated Output (1 kHz) 8 Ω : 60W + 60W
4 Ω : 70W + 70W
Dynamic Power (IFF8 Ω) 190W
Total Harmonic Distortion Factor (T. H. D., 1 kHz) 0.1% or Less (at Rated Output)
0.03% or less (at 10W output)
0.03% or less (at 0.5W output)
Intermodulation Distortion Factor (S. M. P. T. E, 70 hz : 7 khz = 4 : 1) 0.05% or Less (at Rated Output)
Power Band With (IHF, -3dB, THD 0.3%) 10 Hz to 100 kHz
Signal-to-noise ratio (IHF A network, input shunt) 110 dB or more
Damping factor (DC ~ 20 kHz) 8 Ω : 80
4 Ω : 40
Load impedance 4 Ω ~ 16 Ω
Gain 26.5dB
Output terminal Speaker : A, B, A + B switching
Headphone jack
Preamplifier Section
Input Sensitivity / Impedance Phono1, 2 : 1.2 mV, 2.4 mV, 4.8mV/50k Ω
Tuner, AUX1, 2, Play : 100mV/50k Ω
Total Harmonic Distortion Factor (1 v, 1 khz) Not more than 0.03%
Intermodulation Distortion Factor (1 v, S. M. P. T. E, 70 hz : 7 khz = 4 : 1) Not more than 0.05%
RIAA deviation (Phono1, 2) 20 Hz to 20 kHz ± 0.5 dB
Phono maximum allowable input
(1kHz/10kHz, THD 0.1% (R. M.S.))
Input sensitivity 4.8 mv : 500mV/2000mV
Input sensitivity 2.4 mv : 250mV/1100mV
Input sensitivity 1.2 mv : 125mV/550mV
S/N (IHF A network, input shunt) Phono1, 2 : 75 dB or more
Tuner, AUX1, 2, Play : 90 dB or higher
Output Voltage / Impedance
Pre Out (at 100k Ω load) Rated output : 1V/2.7k Ω
Maximum output : 4V/2.7k Ω
Rec Out(Phono) Rated output : 100mV/12k Ω
Tone Control (2 db Step Type) Treble : ± 10 dB at 10 kHz, F-Shift 2 kHz
Bass : ± 10 dB at 100 Hz, F-Shift, 400 Hz
Turnover frequency Treble : 2 khz, 8 khz, Defeat
Bass : 400 Hz, 125 Hz, Defeat
Loudness (at volume -30dB) +5dB/70Hz
Filter High-Filter : 5 kHz, 20 kHz, 6dB/oct.
Low-Filter : 10 Hz, 30 Hz, 6dB/oct.
Muting -20dB
<General>
Semiconductor used Transistor : 42
Diode : 34 pcs
Pwer 100 VAC, 50Hz/60Hz
AC Output Switched : 2 systems, 200 VA
Unswitched : 1 line, 200 VA
Power consumption Electrical Appliance and Material Control Law Standard : 150W
Maximum power consumption : 280W
External dimensions Width 440x Height 150x Depth 386 mm
Weight 12.0kg
Sold Separately Wood Case CW-5 (¥ 3,000)