Accuphase E-210/E-210A
E-210: 170,000yen (April, 1995 release)
E-210A: 190,000yen (April, 1995 release)
Features
Integrated amplifier which supplied the development technology of separate amplifier, renewed the image of the conventional Integrated Amplifier, and investigated cost performance to the limit.
There were two kinds of E-210A which built in E-210 and the equalizer amplifier for analog discs of line amplifier composition.
The power transistor for audios of Oide power
multi-emitter structure excellent in many characteristics, such as a frequency
response, an electric power amplification factor linearity, and switching, is
adopted as the output stage of a power amplifier part. It has structure which
carried out parallel connection of this and was attached to the large-sized heat
sink.
Operation to heat adopted the power MOS FET of the negative
characteristic as the drive stage, the power transistor and heat inclination of
the right characteristic were offset, and stable operation is realized in it.
Although many voltage return types which return a part of Output voltage
to an input are used in the general magnification circuit, in E-210, the current
feedback type magnification circuit which returns an output signal in the form
of current is adopted.
This circuit lowers the impedance of the input
terminal by the side of a return, detects current, carries out I-V
(current-voltage) conversion of that current with a transformer impedance amplifier, and makes an output signal. Since the impedance of a return input
portion is very low, it is hard to generate phase rotation and, as a result,
there is almost no necessity for a phase guarantee.
For this reason, it
excelled in dynamic characteristics, such as a standup, and sound quality is
sharply improved by natural energy response.
The system which inputs
line-in signals, such as CD and a tuner, into direct high gain power amplifier
is adopted.
Even if this system enlarges a gain, by the current feedback magnification
circuit where stability is high, it has acquired the higher effect and
has realized the improvement of many characteristics, such as low noise-izing.
22,000micro of filter capacitors of fx2 are carried in the power-source
part with the large-sized power transformer of about 400 VA.
Since a straight signal course is constituted at the shortest, the logic
relay control system has been adopted.
Adopting the sealed type for communication industry as the relay used by
this system, a contact is the crossbar twin system plated with gold, and
has become a thing of low contact resistance and quantity durability which
has high quality.
The balance input is
carried.
As for balance transmission, the sending side transmits
simultaneously the signal which the phase reversed on the same voltage, and, in
response, the receptacle side is compounded with + amplifier and - amplifier. In
order that the noise ingredient generated in a cable at this time may go into
two poles at this phase, if it is compounded, it will be canceled, and it
disappears by a noise, and the purity of a music signal goes up it.
The
remote commander who can change volume control and input sauce is carried.
Volume control enables smooth operation with the combination of high-quality
sound and a volume controller, and a small motor with a clutch.
Moreover, an
input selector controls a logic circuit by a commander.
The large-sized
speaker terminal which corresponds also to a banana plug and can respond also to
a thick speaker cable is carried.
In E-210A, Phono equalizer amplifier is built in and it has the input circuit
in consideration of the characteristic of each MC/MM type cartridge for
exclusive use.
At the time of MM input, it
constitutes from a low noise FET element which was excellent in the noise
characteristic with high signal source impedance in consideration of an Output
voltage and an Output load impedance being high.
Moreover, at the time of MC
input, since a minute signal is received by low impedance, little reproduction
of noise is enabled by constituting the difference input circuit by a low noise
element, and attaining low impedance-ization of a NFB loop.
There is a Phono equalizer amplifier board of E-210 exclusive use as an option, and upgrade to E-210A is possible.
Model Rating
AD relations are characteristic of the E-210A | |||||||||||||||||||||||||
Model | Integrated Stereo Amplifier | ||||||||||||||||||||||||
Rated continuous average output (Operates on both channels, 20 Hz to 20 kHz) |
110W/ch(4Ω) 100W/ch(6Ω) 80W/ch(8Ω) |
||||||||||||||||||||||||
Total harmonic distortion ratio (both channels) | 0.04% | ||||||||||||||||||||||||
IM distortion factor | 0.01% | ||||||||||||||||||||||||
Frequency characteristics (at rated continuous average output) | High Level input:20Hz~20kHz +0 -0.2dB Low Level input:20Hz~20kHz +0.2 -0.5dB |
||||||||||||||||||||||||
Damping Factor | 110 (8Ω load, 50Hz) | ||||||||||||||||||||||||
Input sensitivity/impedance (Rated output/EIA1W output) |
AD input(MC):0.201mV/22.5μV/100Ω AD input(MM):7.0mV/780μV/47kΩ High Level input:201mV/22.5mV/20kΩ Balanced input:201mV/22.5mV/40kΩ |
||||||||||||||||||||||||
Disc maximum input (Rec out, 1kHz, 0.005% distortion) |
MM:250mVrms MC:7.0mVrms |
||||||||||||||||||||||||
Output Voltage/Impedance | Tape Rec output:200mV/200Ω(from AD, at rated continuous average output) | ||||||||||||||||||||||||
Gain | High Level input → Output:42dB AD input(MM) → Tape rec output:29dB AD input(MC) → Tape rec output:60dB |
||||||||||||||||||||||||
S/N, Input Conversion Noise |
|
||||||||||||||||||||||||
Sub-sonic Filter | 25Hz, -12dB/oct | ||||||||||||||||||||||||
Load Impedance | 4 ohm to 16 ohm | ||||||||||||||||||||||||
Headphone jack | Appropriate impedance: 4Ω to 100Ω | ||||||||||||||||||||||||
Power supply | 100V AC, 50Hz/60Hz | ||||||||||||||||||||||||
Power Consumption | 35W(E-210, no input) 37W(E-210A, no input) 190W(Electrical Appliance and Material Control Law) 315W(at 8Ω load rating) |
||||||||||||||||||||||||
Maximum external dimensions | W475xH150xD417mm | ||||||||||||||||||||||||
Weight | 18.0kg | ||||||||||||||||||||||||
Included:Remote Commander RC-15 | |||||||||||||||||||||||||
Remote control method | Infrared pulse method | ||||||||||||||||||||||||
power supply | DC 3V | ||||||||||||||||||||||||
Batteries | AA 3 (SUM-3/R6), 2 pieces | ||||||||||||||||||||||||
Maximum external dimensions | Width 45x height 136x depth of 18mm | ||||||||||||||||||||||||
weight | 85g (including batteries) |