SANSUI SAX-200
¥ 44,700 (released in 1964)
Commentary
AM/FM multi-stereo amplifier with built-in FM multi-circuit.
The SAX-100 and SAX-200 were the first in the SAX series until around the early 70 s.
The output tube adopts a push-pull configuration of high-efficiency composite tube (3-pole, 5-pole tube) 6BM8.
The power stage has a voltage negative feedback (V-NFB) of more than 16 dB, reducing the internal impedance to approximately 1/8.
Equipped with FM multi-stereo circuit.
Switching matrix method is adopted for the circuit method.
Equipped with a head amplifier that uses four transistors.
We have chosen ultra-precision transistors especially for industrial measuring instruments, and are working to achieve an endless range of products.
Equipped with special terminals for condenser and tweeter.
It is equipped with circuits such as rumble filter, scratch filter, loudness control, friction tone control, FM multiplex, FM-AFC, and tape monitor.
In addition, an FM multiFM multi-indicator for tuning indication.
It uses a mechanism that the colorful scale rises when the power is turned on.
Model Rating
Type | AM/FM multi-stereo amplifier | ||
Power Amplifier Unit | |||
Music power | 23W+23W | ||
Maximum power output | 16W+16W | ||
Frequency characteristic | 20 Hz ~ 80 kHz -2dB or less (8 Ω load) | ||
Distortion factor | 1% or Less (at Output 13W) | ||
Output impedance | 8 Ω, 16 Ω, 32 Ω | ||
Preamplifier Section | |||
Gain (output 12W, 1 kHz) | Phono MAG : 79 dB, 1.1 mV Phono X-TAL : 51 dB, 40 mV Tape (MIC) : 84 dB, 0.8 mV AUX : 46 dB, 70 mV |
||
Signal-to-noise ratio | Tape : 55 dB or more | ||
Tone control | CR Type 50 Hz, + 13 dB to -15dB 10 kHz, + 10 dB to -14dB |
||
Equalizer | NF Type Phono:RIAA Tape:NAP |
||
FM Tuner Section | |||
Receiving frequency | 76 MHz to 90 MHz | ||
Bandwidth | 200kHz(-3dB) | ||
Electrical fidelity | 30 Hz to 15 kHz ± 2 dB or less | ||
Sensitivity | 3.5 μ V (S/N 30 db) | ||
FM Multiplex Section | |||
Method | Switching system | ||
Frequency characteristic | 50 Hz to 15 kHz ± 2 dB | ||
Channel separation | 35 dB (1 V, 1 kHz) | ||
Distortion factor | 1% or Less (0.3 V Input, 1 kHz) | ||
<AM Tuner Section> | |||
Receiving frequency | 535 kHz to 1605 kHz | ||
Bandwidth | 6kHz -3dB | ||
Sensitivity | 50 μ V or More (S/N 20 dB) | ||
<General> | |||
Accessory circuit | Loudness control Scratch filter Rumble filter AFC Tape monitor FM stereo indicator |
||
Semiconductor used |
Silicon Diode SE-0,5B : 2 pcs Selenium Rectifier TC-0,2P : 1 Piece Transistor 2SB-381 : 4 Burr Cap 1S-352 : 1 Piece |
||
Power supply voltage | 100 VAC, 50Hz/60Hz | ||
Power consumption | 120VA | ||
External dimensions | Width 436x Height 147x Depth 343 mm | ||
Weight | 13.3kg |